Search found 1018 matches

by DJ Tucker
Fri Mar 24, 2017 7:53 am
Forum: General Computer Forum
Topic: I bit the bullet. I pre-ordered the best RYZEN chip. [PICTURES INSIDE]
Replies: 21
Views: 813

Re: I bit the bullet. I pre-ordered the best RYZEN chip. [PICTURES INSIDE]

great job on the cable routing. and love the dual side window case. lets get some synthetic benchmarks to stress the system real good :)
by DJ Tucker
Wed Mar 22, 2017 8:32 pm
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

It's a shame you cant just leave a hose on the end coming from the pump and then just get a standard angle barb to fit after that :( I've found a double ended 90 degree barbed compression fitting at last. So what i'm going to do is connect a 3cm piece of tube to the standard fitting on the pump as ...
by DJ Tucker
Tue Mar 21, 2017 4:59 pm
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

ok so after a lot of messaging around I found the measurements of the pump/res and the threaded part is g1/4" and 16mm or 5/8" diameter and the barbed top is 10mm or 3/8" diameter. I need a 90 degree fitting that will screw over that and be at least 25mm tall with a screw cap barbed e...
by DJ Tucker
Thu Mar 02, 2017 3:37 am
Forum: General Computer Forum
Topic: I bit the bullet. I pre-ordered the best RYZEN chip. [PICTURES INSIDE]
Replies: 21
Views: 813

Re: I bit the bullet. I pre-ordered the best RYZEN chip.

yes please. Get posting. don't forget the benchmarks :)
by DJ Tucker
Tue Feb 28, 2017 2:26 pm
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

so I went to my local hardware store and I had no luck at all. They had the right size but the thread was to long and the o ring didn't reach. therefore it would of leaked. I got lucky in finding a black right angle though. That fitted beautifully and would of worked a charm but shame about the shor...
by DJ Tucker
Sat Feb 25, 2017 7:06 pm
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

Tbh I think that's pretty much what I am going to have to do. ghetto modding at its finest :) the hotdog idea is a nice touch. there's a van just outside my local hardware store :lol:
by DJ Tucker
Fri Feb 24, 2017 11:21 am
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

i have already contacted them twice and its been 6 days since my last message and nothing. I took them apart to have a look to see what was underneath. it simply has a tube the connects to the barbed fitting and a screw that goes onto the thread and tightens over the tube just as a hose fastener :)
by DJ Tucker
Thu Feb 23, 2017 8:36 am
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

20170223_141159_800x450.jpg
20170223_141159_800x450.jpg (234.65 KiB) Viewed 257 times

This is a picture of my fittings. As you can see it's barbed but has a threaded bottom. I am looking for a right angle or even a 60 degree fitting to screw on to the thread with a barbed end. If not a barbed end something that I can screw a barbed fitting into :)
by DJ Tucker
Wed Feb 22, 2017 12:02 pm
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

shame they not around now. I live in the uk so scan or overclockers uk is the only real places to go.
by DJ Tucker
Tue Feb 21, 2017 8:33 am
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

i would rather buy them online for aesthetics. could you point me in the direction of the correct part I need to connect a right angled fitting to a barbed fitting with a barbed fitting on the end of that right angle. if not, a right angled fitting that again screws over a barbed fitting with a thre...
by DJ Tucker
Mon Feb 20, 2017 7:37 am
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

well what it seems I need now is a new fitting. I need a 13mm OD/10mm ID right angle fitting that I can screw over the current barbed fitting from the res/pump with a barbed end of that right angled fitting that I can either hose clamp or preferably screw tight?
by DJ Tucker
Sun Feb 19, 2017 8:30 am
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Re: Please Don't Hate!

can anyone help with what i need?
by DJ Tucker
Tue Feb 14, 2017 8:40 pm
Forum: General Computer Forum
Topic: Please Don't Hate!
Replies: 17
Views: 525

Please Don't Hate!

I went ahead and got me a new desk but not any old desk. The Lian Li DK-Q2X. Got it all setup and until the Lepa Exllusion 240 didn't fit as with the tubing, it was too tall. So here is my question. Where in the UK can I get a 90 degree fittings connecting to the cpu block/res with some clear tubing...
by DJ Tucker
Thu Feb 09, 2017 6:07 pm
Forum: General Computer Forum
Topic: AOC G2460VQ6 Dying?
Replies: 3
Views: 238

Re: AOC G2460VQ6 Dying?

well after testing the monitor on another pc I had the same issue. I then decided to try a hdmi cable instead of the display port I was using and that worked great. after checking the display port cable I turn out I had a bent head. tried another display port cable and all works fine at last. I now ...
by DJ Tucker
Tue Feb 07, 2017 5:36 pm
Forum: General Computer Forum
Topic: AOC G2460VQ6 Dying?
Replies: 3
Views: 238

AOC G2460VQ6 Dying?

So my lcd as stated in the title maybe dying. had it a month and randomly it has started to make a several loud click sounds for a minute or so then stop. randomly will start again at any random time within the next 15-30 minutes. what occurs with the clicking is the monitor checkboards or blacks ou...
by DJ Tucker
Thu Jan 26, 2017 5:21 pm
Forum: Cases, Power Supplies, and Cooling
Topic: Toolless PC cases?
Replies: 1
Views: 999

Re: Toolless PC cases?

tbh most well known brands make tool less cases. nzxt, coolermaster, aerocool and lian li to name a few :)
by DJ Tucker
Thu Jan 26, 2017 5:15 pm
Forum: General Computer Forum
Topic: A little treat for me
Replies: 9
Views: 1025

Re: A little treat for me

I personally think it was the Maxwell series as it was the only gpu series I ever had issues on that wasn't my own fault. the only gpu I had issues with was my gtx 580 3gb I had in sli. one overclocked to 850/2000 the other 850/1800. however memory speed matched in evga precision and the other 850/1...
by DJ Tucker
Sun Jan 22, 2017 6:00 pm
Forum: General Computer Forum
Topic: A little treat for me
Replies: 9
Views: 1025

Re: A little treat for me

well it turns out overclockers uk and asus are doing the rma based on my original purchase of the inno3d gtx 980. so I would of got I gtx 1080 if it had been a 980 ti I had purchased. instead I have got the asus dual gtx 1070 that I am installing as I write this. its a shame as the performance is ar...

Go to advanced search