Lapping Guide

Want to show off that smoking system or your latest creation?
User avatar
DMB2000uk
Site Admin
Site Admin
Posts: 7095
Joined: Mon Jul 18, 2005 5:36 pm
Location: UK

Lapping Guide

Post by DMB2000uk »

Lapping Guide By Dan ^_^

Introduction

If you are a hardcore overclocker, or a temperature junkie, you may have considered lapping your heatsink, but how many of you have considered that your IHS* may have just as many imperfections as your heatsink?

Now for those of you that don't have a clue what I'm talking about when I say lapping, let me give you a little lesson. The process (or art) of lapping is to sand down imperfections in the smoothness of your heatsink or IHS to give the flattest surface possible. One of the side effects of making a metal as flat as possible is that it gets shiny (As totally flat things reflect light better), and if you continue the lapping process far enough you will end up with a mirror finish. The reason we need the surface as flat as possible is so that the heatsink and processor can make more contact and more efficiently conduct the heat away.

Now you may be thinking why aren't all processors and heatsinks made to a mirror shine from the factory if it is so good, but the reality is that improving the already fairly flat surface of most heatsink/IHS's to mirror shine will only realise an average 2-3oC drop in temperatures. So with such little to gain from so much work, why would anyone do it? Well for the same reasons that people overclock their system as much as it physically will go. And as all overclockers will, or should know, cooler temperatures allow processors to be pushed further. So that is why I want to lap my processor!

Before I detail the lapping process, I have to give a warning. This is something that can me messed up very easily, so don't try this if you cannot afford to replace what you could break. It is a long and tedious venture, so if you have no patience then this is probably not for you. Be prepared to get messy, water with grit/filings is hard to get out of clothes/furniture so work somewhere that you can clean up easily, and/or put down some newspaper on your work surface.

OK, for those of you still with me, lets get down to the good stuff!


*(IHS is short for Integrated Heat Spreader, and its job is to spread the heat from the processor core so that it can be more efficiently removed to keep the processor cooler. Its secondary function serves to protect the core from damage from too much pressure from heatsinks etc.).

_____________________________________________________________

What you will need is:
  • A flat work surface, and/or piece of glass;
    Somewhere that is smooth so we don't get bumps under the sandpaper meaning we would be sanding unevenly

    Wet and dry sandpaper, ranging from 400 grit to 2500 grit;
    (If you can only find up to 1500 grit that should be OK, it will just mean that your finished project will not be as mirror finished as something done with 2500 grit, but it will still be flat, which is what we need here)

    Water;
    To use as lubricant for the sanding and to rinse off filings, so a sink near by is proffered

    Heatsink/Processor to lap;
    Obviously ^_^


Now I thought that it would be fairly easy to find sandpaper to at least 1500 grit at my local hardware store, so I made a journey out to a B&Q warehouse to see what they had in. Unfortunately the grades of sandpaper I would need were to prove to be more elusive than I originally thought as B&Q only had wet and dry that went up to 600grit, much lower than what I needed. So I bought a pack of 200, 400, 600 in the hopes of finding some finer stuff elsewhere. But I could not. I have since learnt that I was looking in the wrong places and would have probably had more luck in somewhere that is specialised in cars!


So still wanting to lap my processor I had to search elsewhere for the needed grade papers. So I turned to KustomPCs.co.uk and purchased a lapping kit, complete with glass to sand on. There are a total of three kits to choose from and I chose the premium kit at £12. If you don't think you'll need the glass, or aren't fussed about getting the best mirror shine possible, then one of the basic kits would be better suited for you. These kits are available internationally from various resellers. The kit I chose has 400, 600, 800, 1000, 1200, 1500, 2000 and 2500 grit. (If you choose to purchase your sandpaper individually you could probably get away with skipping 1200 and maybe 800 if you can't find it).


So kit in hand I set about to join the hardcore enthusiast and lap my processor.

_____________________________________________________________

Image

The kit comes with some handy hints and tips to a successful lap. The technique is to wet the sandpaper, so that it sticks to the glass, and also lubricates the processor while lapping. And with minimal force pressing down move the processor backwards and forwards across the sandpaper. Add more water if you feel it dragging too much and alternate the direction of sanding evenly. Slow and steady wins the race in this game, so don't go too fast when sanding.


Some people suggest sanding in a figure of 8, but for best mirror results it is best to only sand perpendicular strokes.


Image

My victim. Start with your CPU cleaned of any TIM and ready to lap.


Image

While researching peoples techniques to lapping I came across this method of drawing a grid with a Sharpie (or CD/DVD type pen) all across the surface. This allows you to more easily see which areas of the surface are getting lapped, and also allows you to check that you are applying even pressure.


Image

Straight away you can see the irregularities on my processor IHS, it seems to be convex in the middle with a lip round the edge. I suspect that the lip round the edge is higher than the middle and as such limits its conductivity.


Image

After a while with the 400 grit, you can start to see it becoming reflective already. You should continue with this layer until you can not see any more marker on the top.


Image

I tried the 600 grit for a while, but some stray material got on the sheet and put a nice scratch along the bottom here. See what I mean about it being easy to mess up? Back to 400 grit I go to remove the scratch.


Image

This is after the 400 grit again. Once the initial flattening has been completed (aka 400 grit), the other layers should only take 5-10 minutes each, as their only purpose is to remove the scratches created by the previous sandpaper.


Image

Now the 600 grit.


Image

After the 800 Grit, a nice mirror effect is starting to appear.


Image

1000 grit also done; notice that the top layer of nickel is mostly gone and the copper underneath is showing. There is still plenty of material left, so don't worry that you are sanding too far through the copper. To remove all the copper would take days at the rate of sanding we are going.


Image

1200 grit finished, over halfway done now


Image

1500 grit, at this point I was beginning to get bored, so probably rushed the next few levels of sandpaper


Image

After 2000 grit, the end is now in sight, with only one level left to go


Image

And my finished product, after 2500 grit.


Image

Look at that for mirror effect. Now that I've done all that hard work, lets go put the stock thermal pad back on and see what a difference its made*.






*Artic Silver 5 was used as the thermal interface material (If you do lap a heatsink or CPU then use a thermal pad I will personally come round and confiscate your system. Make sure that you have a high quality TIM after you have put in all this effort)

____________________________________________________________

Testing

Image

The test setup was as follows:
  • Core2Duo E6600 @ 2448Mhz,
    XFX 7900GS XT,
    WD Caviar 160GB x2 in RAID-0,
    2GB Crucial Ballistix PC6400 DDR2 (4-4-4-12),
    Abit A9WD-MAX,
    XP Pro
Temperatures were recorded using Core Temp 0.95. Load readings were taken after 30 minutes of ORTHOS stressprime 2004. Idle readings were taken after 30 minutes of sitting at the desktop idle. Ambient: 25oC. Artic Silver 5 was used as the thermal interface material.

Image
Core Temp 0.95



Results

Temps were:
Original
  • Idle@25oC ambient: 32, 35
    Load@25oC ambient: 52, 52
Lapped
  • Idle@24oC ambient: 29, 32
    Load@24oC ambient: 51, 51
Image

Even without the needed burn in time to get optimal performance from the Artic silver, we can see that there is already a 2oC difference in idle temps. With proper time for the thermal paste to cure this temperature will only get better.


Image

However, the load temperatures are not quite as impressive, and it shows that the paste still needs further curing to leave behind the temperatures from the original tests. However, given time to fully burn in, this performance should surpass the unlapped temperatures even more.

_____________________________________________________________

Conclusion


Artic silver needs to be given a cure time of several days for it to perform to the best of its abilities. It needs several cycles of full load and complete cool down (i.e. System powered off) to be able to perform at its best. Without letting the Artic silver cure properly (it had less than 24 hours and only a few power cycles) it is naturally not performing the best it can. But if initial results are anything to go by then I should be able to look forward too even cooler temperatures yet.


When lapping my processor I was unsure of how much material the finishing layers would take off after the 400 grit, so I did not remove as much as the nickel top layer as I could have done. So as a result there are still a small amount of 'unfinished' bits on my IHS (where there is nickel covering the IHS still), however these 'imperfections' are at the edges of the processor and the hot core is in the middle. So this should not really impact performance, but for aesthetics sake, I may choose to start this whole process over and make my processor completely flat and mirror like at some point in the near future.


Bottom Line:


If you don't have patience then lapping is definitely not for you. But if you are looking to push your system as far as you can, or you long to have it run a degree or two cooler, then lapping is definitely something you should consider.
Last edited by DMB2000uk on Mon Jul 23, 2007 1:05 pm, edited 1 time in total.
Image (<- Clickable)
User avatar
kappage
Legit Extremist
Legit Extremist
Posts: 1356
Joined: Mon Aug 28, 2006 11:38 pm

Post by kappage »

I'll say this, your crazy now can i have the CPU?? It looks like it might be in safer hands. :ANAL: :ANAL: :ANAL: :ANAL:
Main Rig: C2D 6850 @ 3.0Ghz, 2Gb DDR2667Mhz @ 833Mhz 5-5-5-15 Timings , XFX xXx 8600GTS @ 730/2260 , Gigabyte Ga-945GCM-S2L
JukeBox: Currently in an Upgrade but im too lazy to do it at the moment
I² keepin it real
User avatar
Apoptosis
Site Admin
Site Admin
Posts: 33941
Joined: Sun Oct 05, 2003 8:45 pm
Location: St. Louis, Missouri
Contact:

Post by Apoptosis »

Great post reminds me of my lapping article: http://www.legitreviews.com/article/402/1/
User avatar
DMB2000uk
Site Admin
Site Admin
Posts: 7095
Joined: Mon Jul 18, 2005 5:36 pm
Location: UK

Post by DMB2000uk »

kappage wrote:I'll say this, your crazy now can i have the CPU?? It looks like it might be in safer hands. :ANAL: :ANAL: :ANAL: :ANAL:
Lol, would it really be, with you breaking things? :P

Apoptosis wrote:Great post reminds me of my lapping article: http://www.legitreviews.com/article/402/1/
Yeah, but unlike you're article I don't plan on taking off the IHS and killing it :mrgreen:

Dan
Image (<- Clickable)
User avatar
dicecca112
Site Admin
Site Admin
Posts: 5014
Joined: Mon Mar 01, 2004 10:40 am
Contact:

Post by dicecca112 »

very well done my friend. Stickied
Image
User avatar
DMB2000uk
Site Admin
Site Admin
Posts: 7095
Joined: Mon Jul 18, 2005 5:36 pm
Location: UK

Post by DMB2000uk »

Aww Nice :mrgreen:

Thank you very much.

Dan
Image (<- Clickable)
User avatar
KnightRid
Moderator
Moderator
Posts: 4295
Joined: Wed Dec 14, 2005 5:21 am
Location: Dallastown, PA

Post by KnightRid »

Will you be updating this in a week or 2 with the new tempo readings?

I am curious to see how much of a difference there will be after the AS5 sets up.

Mike

I have NO patience, so I might never try this, but it is a hell of a walkthrough! THANX!
Remember, I am opinionated and nothing I say or do reflects on anyone or anything else but me :finga:
User avatar
kappage
Legit Extremist
Legit Extremist
Posts: 1356
Joined: Mon Aug 28, 2006 11:38 pm

Post by kappage »

Bah, Course it would be!
Main Rig: C2D 6850 @ 3.0Ghz, 2Gb DDR2667Mhz @ 833Mhz 5-5-5-15 Timings , XFX xXx 8600GTS @ 730/2260 , Gigabyte Ga-945GCM-S2L
JukeBox: Currently in an Upgrade but im too lazy to do it at the moment
I² keepin it real
User avatar
kenc51
Legit Extremist
Legit Extremist
Posts: 5167
Joined: Thu Jun 23, 2005 1:56 pm
Location: Dublin, Republic of Ireland
Contact:

Post by kenc51 »

I might try this soon.........I'll have some more "parts" ordered this week :finga:

Great job Dan! =D>
Solinari
Legit Aficionado
Legit Aficionado
Posts: 61
Joined: Wed Jun 13, 2007 11:16 am

Post by Solinari »

Good results, i have seen another dude in a similar forum that did it to a Quad Core CPU. Frankly i thought he was nuts doing it to such an expensive CPU on a first attempt, but he did seem to get decent results.

I am not sure about doing it myself, i don't have a spare CPU nor the means to buy one and i am quite happy with my temperatures at the moment. I would consider it after doing to an older CPU first then see how it went.

Good guide though, i'll keep this one in my aptly named 'useful sites' bookmark folder :P
AMD Athlon 64 x2 3800 @ 2.7Ghz
Asus A8N32-SLI Deluxe
eVGA 8800GTS 640MB SuperClocked
A-Data 2GB DDR400
Integrated Sound
Hiper Type-M 580W PSU
jtleon
Legit User
Legit User
Posts: 6
Joined: Mon Aug 28, 2006 2:48 pm

Re: Lapping Guide

Post by jtleon »

Outstanding article....Great Job!
Regards,
jtleon
Iwill DH800 - Xeon SL74T LVs @ 3.5Ghz - Mushkin 2Gb ES @ FSB233 - Gainward 7800GS+ 512Mb
AMS 460W XPS - 100% 3D Stable to 85°F (30°C) Ambient
User avatar
stopthekilling77
Legit Extremist
Legit Extremist
Posts: 2188
Joined: Fri Feb 02, 2007 2:08 pm
Location: Colorado, USA

Re: Lapping Guide

Post by stopthekilling77 »

However, the load temperatures are not quite as impressive, and it shows that the paste still needs further curing to leave behind the temperatures from the original tests. However, given time to fully burn in, this performance should surpass the unlapped temperatures even more.
hey dan! saw this thread get bumped today, and was wondering about the load temps now that its been a month since posting.
Cyberpower generic case
B450M PRO-VDH MAX
Ryzen 5 3600 w/PBO/OC
CM Hyper 212 EVO push/pull
Corsair VENGEANCE LPX 16GB (2 x 8GB) DDR4-3600 CL16
MSI RTX 3060 Ti Ventus 3X 8G OC LHR
Samsung 970 EVO Plus 500GB
6GB Seagate HDD
EVGA 650BQ 650W PSU
ASUS VE278 27" monitor, Dell E2216HV (vertical)
Logitech Z533 2.1 Speakers, G935 7.1 or G435 headset
MS LXM-00001 keyboard
Razer Deathadder Elite, XBOX One Lunar Shift controller

I've come a long way from my original Core2Duo E6750 build y'all! :supz:
User avatar
DMB2000uk
Site Admin
Site Admin
Posts: 7095
Joined: Mon Jul 18, 2005 5:36 pm
Location: UK

Re: Lapping Guide

Post by DMB2000uk »

Yeah about that :roll:

I got fed up of the noise so put my rig back together with my waterloop, so its kinda messed with any before and after results I might of had.

Not that its any compare, but my fans are now at 6v (22oC ambient), and I get 33oC, 31oC in idle and 43oC 43oC load.
(At 12v I get 41oC 41oC load (same ambient) and 27oC 30oC idle).

Those above stats weren't tested as exhaustively as the lapping ones were, so may be off in the long term results (I could only be bothered to wait 10mins for the results and was still doing other stuff).

Going to see what a difference switching to Arctic Cooling's MX2 makes to Arctic Ceramique, according to AC's stats its supposed to be a couple of degrees cooler.

I love being a temperature junkie ^_^

Dan
Image (<- Clickable)
FeRaL
Legit Extremist
Legit Extremist
Posts: 355
Joined: Wed Sep 20, 2006 3:14 pm
Location: So Cal

Re: Lapping Guide

Post by FeRaL »

Just wondering, did you use anything to protect the other side of the processor from the slurry that results from the water, soap, and metal particles?

I've seen in the past where people had tapped up pretty much all of the processor except for the part being lapped.
User avatar
Zertz
Legit Extremist
Legit Extremist
Posts: 1118
Joined: Tue Mar 20, 2007 4:19 pm
Location: Magog, Quebec

Re: Lapping Guide

Post by Zertz »

FeRaL wrote:Just wondering, did you use anything to protect the other side of the processor from the slurry that results from the water, soap, and metal particles?

I've seen in the past where people had tapped up pretty much all of the processor except for the part being lapped.
You can sit it in foam or something similar. LGA775 processors don't actually have pins so that's one thing you don't have to worry about.
User avatar
DMB2000uk
Site Admin
Site Admin
Posts: 7095
Joined: Mon Jul 18, 2005 5:36 pm
Location: UK

Re: Lapping Guide

Post by DMB2000uk »

I just put the plastic cover on that came with the chip, not water proof by any means, but enough to protect it.

Dan
Image (<- Clickable)
User avatar
siicogamer
Legit Enthusiast
Legit Enthusiast
Posts: 48
Joined: Fri Jul 20, 2007 5:50 am
Location: Melbourne,Australia

Re: Lapping Guide

Post by siicogamer »

so i can do this with any cpu? because i wanna try this on my amd 1800+ @1.54ghz
User avatar
DMB2000uk
Site Admin
Site Admin
Posts: 7095
Joined: Mon Jul 18, 2005 5:36 pm
Location: UK

Re: Lapping Guide

Post by DMB2000uk »

Yeah you can do it on any CPU, just as long as it has a protective IHS over the core.

Good luck and have fun! (And remember you can't blame me if you do it wrong :P)

Dan
Image (<- Clickable)
User avatar
siicogamer
Legit Enthusiast
Legit Enthusiast
Posts: 48
Joined: Fri Jul 20, 2007 5:50 am
Location: Melbourne,Australia

Re: Lapping Guide

Post by siicogamer »

Yeah you can do it on any CPU, just as long as it has a protective IHS over the core.
i don't have it anymore...crap....
SlipSand
Legit Fanatic
Legit Fanatic
Posts: 144
Joined: Tue May 25, 2004 6:50 am
Location: NC

Re: Lapping Guide

Post by SlipSand »

This seems kinda riskay...And will deff void your warranty.

You could however get out more impurities with some rubbing and polishing compund then clean it off with a little bit of alcohol. It will never be perfect however.
Image
Post Reply