DDR2-667 Memory showing as 625Mhz

From general questions to the harder advanced user topics you will find them here!
Post Reply
User avatar
Kaos Kid
Legit Extremist
Legit Extremist
Posts: 958
Joined: Sat Mar 27, 2010 11:31 am
Location: 40 clicks West of the Gateway

DDR2-667 Memory showing as 625Mhz

Post by Kaos Kid »

While goofing around with an old Compaq board and 4GB of HP branded (Micron) DDR2-667 memory (PC2-5300), I noticed that in both AIDA64 and CPU-Z the memory shows as operating at 625 (312.5x2) instead of 667 (333.5x2). I can't figure out why it doesn't run at full speed, since they should be entirely compatible. I also see that the memory multiplier/divider is CPU-DRAM 9. Is there a good reason why it doesn't show as running at the full spec? The timings do show up as correct for 667 (5-5-5-15) so I'm not sure why, unless it is just a limitation of the Narra3 Compaq mobo. There are no bios updates available for it on the Compaq site. In fact, this mobo doesn't even have official WinXP drivers, Compaq only offers Vista drivers. I have WinXP 32bit installed, and am using the Nforce 15.26 drivers, which seem to work fine. Could they be the reason? Note: This is an OEM bios that doesn't allow any changes to FSB or memory configs, so I'm stuck with defaults.

Another question: If you had the choice between either...

1) 4 x 1GB of DDR2-667 running at 625Mhz @ 5-5-5-15 (dual channel)

2) 1 x 1GB of DDR2-800 running at 800Mhz @ 5-5-5-15 (single channel)

3) 2 x 512mb DDR2-800 running at 800Mhz @ 6-6-6-18 (dual channel)

Which would you choose for a box (with the OEM Compaq) that would basically be an internet surfer? I'm not sure that having 4GB is really going to help that much, and with the 32-bit limitation not all is assignable anyway. I did try putting the 2x512mb of DDR2-800 in the first two slots and the 1x1GB of DDR2-800 in the 3rd slot, but it dropped all the memory to PC2-5300 in the bios, and put all the timings to 5-5-5-15, so it seemed the same as if I would have just used 2x1GB of the actual DDR2-667. I would have thought that it would have stayed at PC2-6400 but loosened the timings of the faster RAM to 6-6-6-18 instead of keeping the 5-5-5-15 and lowering the clock speed. Can anyone shed some insight on this?
I have come to the conclusion that "FaceBook" should be renamed "FacePalm" :roll:
User avatar
skier
Moderator
Moderator
Posts: 4450
Joined: Mon Mar 26, 2007 3:29 pm
Location: Maine
Contact:

Re: DDR2-667 Memory showing as 625Mhz

Post by skier »

who cares about speed, with less than 2GB of memory i dont find computers ever usable for anything, use 2x1GB ddr2 667 at 625 and call it a day.
-Austin
Image
Screamin' BCLK: Image
775 System (Overclocking Platform): Q8400/Q8300/E8400/E7400/E7500 - GA-EP45-UD3R v1.1 - 4GB (2x2) OCZ Reaper HPC DDR2 1066 CL5 2.1v Corsair TX-750w
Gamer: Asrock Z77 Extreme4, i7 3770K @4.6GHz, ThermalTake Armor A90 modded, 2x4GB GSKILL RipjawsX DDR3 2133 CL9, Corsair HX-750w, MSI GTX660 Twin Frozr
Server2012: Q9300 - 8GB DDR2 - Asus P5QL Pro - Corsair CX430 - Mirrored 2TB Seagate's with 2TB WD cav for fileshare backups, 1TB WD for OS backups
Post Reply