Page 1 of 1
My benching setup - What a mess!
Posted: Sat Dec 01, 2007 10:22 am
by kenc51
The pic is bad quality for some reason, it happened after I resized it, but you get the message
This is my current bench setup. I stripped down the rig earlier this week.
This should be a PSA for how
NOT to do it ;)

- messy.jpg (128.46 KiB) Viewed 4485 times
& this is how it should be done!

Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 10:31 am
by Bio-Hazard
I'd say that you have your work cut out for yourself getting that mess all straighten up.............
But I have faith that you'll get it done.
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 10:38 am
by dicecca112
dude its called a can of compressed air, clean those fans man
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 11:14 am
by Major_A
I've seen worse, it was called the back of my desk. All you need is to dust that beast and use a lot of zip ties/cable ties.
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 3:54 pm
by DMB2000uk
dicecca112 wrote:dude its called a can of compressed air, clean those fans man
If you are talking about the fan on his 8800GTS, isnt that the one he bought just couple of weeks back? So its probably just the fan colour/bad pic making it look dusty
Well if you had a torture bench like LR does, then I'm sure that you could tidy the cables easier
Dan
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 4:19 pm
by dicecca112
nope the case fans on the back
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 4:41 pm
by DMB2000uk
dicecca112 wrote:nope the case fans on the back
>_< I was looking for dust on ken's bench, not nate's or whoever's the torture rack was
Dan
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 5:15 pm
by kenc51
DMB2000uk wrote:dicecca112 wrote:nope the case fans on the back
>_< I was looking for dust on ken's bench, not nate's or whoever's the torture rack was
Dan
The torture rack was from pastorjay's mobo review, hence the LR watermark
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 5:56 pm
by Methious
Hey don't feel bad up til last month I had my work bench rig hanging on the wall on a piece of plywood, covered in a plexi shroud. Local tech school bought it and I switched to a full tower setup.
Seems like every time I get all the cables strapped in just right a new part comes through the door and I gotta re-strap.
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 6:13 pm
by Bio-Hazard
Cleanliness is next to godliness, you gotta keep those systems clean if you want them to take care of you. .............

Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 6:17 pm
by kenc51
No-one noticed the dead gfx card in the back, it was an X1900XTX

Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 6:20 pm
by DMB2000uk
kenc51 wrote:No-one noticed the dead gfx card in the back, it was an X1900XTX

It's been swallowed by the mess of wires, and the low quality pic makes it ahrd to pick out details
Dan
Re: My benching setup - What a mess!
Posted: Sat Dec 01, 2007 6:30 pm
by skier
it must be playing hide and seek with the camera

, i cant see it at all, i can barely make out the HDD
is that setup like, half in a tower and half on the floor?? because it looks like i can see the expansion slots in the upper left corner of the pic