My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
Never had flashy lights in any of my cases, and the ones that come with them I cut them out. I don't even hook up activity lights LOL
"The democracy will cease to exist when you take away from those who are willing to work and give to those who would not."
-Thomas Jefferson
-Thomas Jefferson
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
nice work~~~
but I'm a little curious about the screw on the daughtercard...
that doesn't make sense to use only 2 holes to fasten the board into chassis...
can't I just remove the nut and use the same screw on the daughtercard to fasten the board???
but I'm a little curious about the screw on the daughtercard...
that doesn't make sense to use only 2 holes to fasten the board into chassis...
can't I just remove the nut and use the same screw on the daughtercard to fasten the board???
- Apoptosis
- Site Admin
- Posts: 33941
- Joined: Sun Oct 05, 2003 8:45 pm
- Location: St. Louis, Missouri
- Contact:
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
You could remove the screw on the daughter card and buy the right size screw that is longer and put it to the motherboard I assume. The screws are to hold down and to help keep the ASUS DIGI+ VRM secure on this ITX board. I attached a larger picture for you to see. The board doesn't move that much, so I don't think it is a big concern. I talked to ASUS about it as I was concerned when I first saw this, but no they said not to worry and I've had zero issues at all with this platform and have had it running for a couple weeks now.
- Attachments
-
- top-bracket.jpg (94.85 KiB) Viewed 13695 times
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
Nice build!
If you don't mind me asking... what fans did you use for this?
If you don't mind me asking... what fans did you use for this?
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
And actually, since you mentioned in the article that the CoolIT 140 was hard to come by... Do you think using a 120mm solution with a 140 to 120 adapter to mount the radiator to the case would still fit?jtiger102 wrote:Nice build!
If you don't mind me asking... what fans did you use for this?
I found this adapter: http://www.frozencpu.com/products/9003/ ... 47c121s262
It says it's 14mm in depth. Judging by the pictures, there might be enough room to insert the adapter between the radiator and the case.
Thanks!
- Apoptosis
- Site Admin
- Posts: 33941
- Joined: Sun Oct 05, 2003 8:45 pm
- Location: St. Louis, Missouri
- Contact:
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
Yeah, I don't think you'll have any issues with that adapter at all! I just used some generic high-pressure 140mm static fans that I had here. I can't recall the brand and they have no markings on them.jtiger102 wrote:And actually, since you mentioned in the article that the CoolIT 140 was hard to come by... Do you think using a 120mm solution with a 140 to 120 adapter to mount the radiator to the case would still fit?jtiger102 wrote:Nice build!
If you don't mind me asking... what fans did you use for this?
I found this adapter: http://www.frozencpu.com/products/9003/ ... 47c121s262
It says it's 14mm in depth. Judging by the pictures, there might be enough room to insert the adapter between the radiator and the case.
Thanks!
- Apoptosis
- Site Admin
- Posts: 33941
- Joined: Sun Oct 05, 2003 8:45 pm
- Location: St. Louis, Missouri
- Contact:
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
Here is another persons build in a Silverstone case with a 120mm version of the CoolIT Eco II running an Intel Core i7-3770K processor and the ASUS P8Z77-I Deluxe mini-ITX Z77 Motherboard
.
.
Re: My 2012 Project: Water Cooled Mini ITX PC w/ Ivy Bridge
Actually, the user manual recommends doing what cozy said: remove the screws from the Vcore card, install the MOBO in your chassis, then replace the screws. It's on page 2-34.Apoptosis wrote:You could remove the screw on the daughter card and buy the right size screw that is longer and put it to the motherboard I assume. The screws are to hold down and to help keep the ASUS DIGI+ VRM secure on this ITX board. I attached a larger picture for you to see.
Sorry if I'm pointing out the obvious here, but I'm just curious why you wouldn't follow the manual, regardless of whether the board will actually move or not.