Legit Reviews

Hallo everybody .. its my firts post here, so I would like to welcome the Legit Reviews community.

(Sorry for ma bad english its not the language that I use everyday)

The config of my pc:
CPU:Sempron 2800+ (def. 1.6Ghz 1.4V @ 2.9Ghz 1.7V) without the IHS http://www.morpheus.somee.com/fotki/superpi6.jpg
Mainboard: Gigabyte GA-K8NS nForce3 250Gb
Mem: 512
G.card: Radeon9800Pro
PSU: Tagan U01 380W
Case: Chieftec LBX-03

Parts of the water cooling system:
cpu: F2S (by Samhain - http://www.realitynet.pl - )
gpu: Cube (by Misiu15go)
chipset: DFI pro (by Misiu15go)

http://info.wsisiz.edu.pl/~miazgows/wc/rev5-2.jpg
http://info.wsisiz.edu.pl/~miazgows/wc/rev5-9.jpg

pump: Atman-305
http://info.wsisiz.edu.pl/~miazgows/wc/atman1.jpg

radiator: "pimped" Fiat 125 ;) + 2x120mm fans
http://info.wsisiz.edu.pl/~miazgows/wc/fiat1.jpg
http://info.wsisiz.edu.pl/~miazgows/wc/fiat2.jpg


-------------------------------------------------------------------------------------------------------------------------------------

Its nice .... isnt it? ;)
The reason I build it was silence the other thing is for sure overclocking :D

Temperaures:
cpu: idle/stress 28-30/33-35C
cpu @2.9Ghz stress ca.40-45C[/b][/code]

More pics on my page http://info.wsisiz.edu.pl/~miazgows/revizja5.html

that's a nice, clean frigging case, dude. very nice.

i'm jealous.

by the way, your english seems fine it's actually better than some of the other forum members'

Welcome!!!

Watercooling is the only way to go IMO.....

I can't stand the noise of air cooling.....

Very nice! You should post a pic of your whole case - I'd like to see it.

Nice looking rig.............

I've seen those blocks before somewhere, I think over at System Cooling.

FZ1 wrote:Very nice! You should post a pic of your whole case - I'd like to see it.

Its nothing special. I havent changet it a lot.
Here you can see a earlier version and the top of the case http://morpheus.cba.pl/bok5.html

nice, clean looking mod and good prformance
WELCOME !!!!!!

agreed very clean very nice.

Just an update
I changed the config a little bit and here are the pics (already 1.5 years old ;):



































CPU: X3N
GPU: Cube
NB: Cube DFI Pro
Pump: Atman 305 @ inline
Radiator: Cooltek 120 Dual
Rez: Realitynet 1x5.25
Tubes: Cellfast 10/13

Some more pics at my page http://info.wsisiz.edu.pl/~miazgows/revizja6.html

Nice clean build............

Bio-Hazard wrote:Nice clean build............

Thank you for that one comment.

I guess this LR Forum is dead

No actually it's a quite active forum, older threads and such fall off the beaten path.

What type of tubing is used?

Do the tubes seal on the fittings with heat?

A nice clean setup without using clamps.

Glad you updated the cooling system loop. Nice to see pictures.

Tubing? Hmmm just an ordinary tubing of universal use 10/13mm. I've bought it in a garden shop. http://www.cellfast.com.pl/products/index/26
You don't need to use clamps on those fittings 10/12mm, cuz they are one size bigger then tubing. Actually its hard to take them off ;)

heh, I remember reading this thread and being really impressed with how clean the setup was. Apparently I didn't stop and comment that. (must have gotten distracted >_<)

Dan

I think in about one week, i'll update the photos once again.
Im going to buy a new pump and probably a reservoir (im not sure of it yet http://www.cooling.pl/black-water-otank ... ,2034.html )
I'll try to keep the rig in the same "clean" way as it was.

Very very impressive rig, that is awesome. i like the water cooling.