POST Crashing?
POST Crashing?
Hi guys.
Got me a new PC and all seemed well but after it has done the POST it seems to crash. So I reboot and all is well.
Any ideas??
Neptune24
Got me a new PC and all seemed well but after it has done the POST it seems to crash. So I reboot and all is well.
Any ideas??
Neptune24
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600)
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
- DJ Tucker
- Legit Extremist
- Posts: 1502
- Joined: Tue Dec 30, 2008 11:52 am
- Location: Hardbase Headquaters
- Contact:
Re: POST Crashing?
does it crash just before the log in screen appears as mine did that and it turnt out to be cpu fault. go into your bios and check your cpu is at the stock speed!
MSI Z590 Gaming Edge Wifi
Core i7 10700KF 5Ghz @ 1.25v With Alphacool Eisblock XPX Aurora Edge
Gigabyte RTX 2080 Super 1980Mhz @ 0.925v With TechN GPU Block
32Gb Corsair Vengeance RGB Pro 3600Mhz 16-18-18-38
Aqua Computer Ultitube 200 Pro D5 Next
Corsair XR5 240mm x2 & 360mm
Intel 670p 2Tb & WD Blue M.2 2Tb
Corsair HX1000i
Philips Momentum 3000 24" (Main) & MSI Optix G241V E2 (Second)
Lian Li O11D
Roccat Vulcan 120 Aimo, Roccat Kone Aimo Remastered and Roccat Sym Pro Air
Core i7 10700KF 5Ghz @ 1.25v With Alphacool Eisblock XPX Aurora Edge
Gigabyte RTX 2080 Super 1980Mhz @ 0.925v With TechN GPU Block
32Gb Corsair Vengeance RGB Pro 3600Mhz 16-18-18-38
Aqua Computer Ultitube 200 Pro D5 Next
Corsair XR5 240mm x2 & 360mm
Intel 670p 2Tb & WD Blue M.2 2Tb
Corsair HX1000i
Philips Momentum 3000 24" (Main) & MSI Optix G241V E2 (Second)
Lian Li O11D
Roccat Vulcan 120 Aimo, Roccat Kone Aimo Remastered and Roccat Sym Pro Air
-
- Legit Extremist
- Posts: 605
- Joined: Mon Jan 31, 2011 11:51 am
Re: POST Crashing?
No it finishes the IDE detection and then seems to crash. All of the levels are factory as I don't like overclocking (too much risk and fiddling).
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600)
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
- DJ Tucker
- Legit Extremist
- Posts: 1502
- Joined: Tue Dec 30, 2008 11:52 am
- Location: Hardbase Headquaters
- Contact:
Re: POST Crashing?
do you have any IDE controllers or even old IDE hard drive or cd/dvd drive if not disable IDE detection in your bios. that may stop your problems.
MSI Z590 Gaming Edge Wifi
Core i7 10700KF 5Ghz @ 1.25v With Alphacool Eisblock XPX Aurora Edge
Gigabyte RTX 2080 Super 1980Mhz @ 0.925v With TechN GPU Block
32Gb Corsair Vengeance RGB Pro 3600Mhz 16-18-18-38
Aqua Computer Ultitube 200 Pro D5 Next
Corsair XR5 240mm x2 & 360mm
Intel 670p 2Tb & WD Blue M.2 2Tb
Corsair HX1000i
Philips Momentum 3000 24" (Main) & MSI Optix G241V E2 (Second)
Lian Li O11D
Roccat Vulcan 120 Aimo, Roccat Kone Aimo Remastered and Roccat Sym Pro Air
Core i7 10700KF 5Ghz @ 1.25v With Alphacool Eisblock XPX Aurora Edge
Gigabyte RTX 2080 Super 1980Mhz @ 0.925v With TechN GPU Block
32Gb Corsair Vengeance RGB Pro 3600Mhz 16-18-18-38
Aqua Computer Ultitube 200 Pro D5 Next
Corsair XR5 240mm x2 & 360mm
Intel 670p 2Tb & WD Blue M.2 2Tb
Corsair HX1000i
Philips Momentum 3000 24" (Main) & MSI Optix G241V E2 (Second)
Lian Li O11D
Roccat Vulcan 120 Aimo, Roccat Kone Aimo Remastered and Roccat Sym Pro Air
Re: POST Crashing?
I do have an IDE disk drive which at the mo has a game inside nearly all the time. Could that cause the issue??
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600)
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
- DJ Tucker
- Legit Extremist
- Posts: 1502
- Joined: Tue Dec 30, 2008 11:52 am
- Location: Hardbase Headquaters
- Contact:
Re: POST Crashing?
you mean HDD or cd/dvd drive?
MSI Z590 Gaming Edge Wifi
Core i7 10700KF 5Ghz @ 1.25v With Alphacool Eisblock XPX Aurora Edge
Gigabyte RTX 2080 Super 1980Mhz @ 0.925v With TechN GPU Block
32Gb Corsair Vengeance RGB Pro 3600Mhz 16-18-18-38
Aqua Computer Ultitube 200 Pro D5 Next
Corsair XR5 240mm x2 & 360mm
Intel 670p 2Tb & WD Blue M.2 2Tb
Corsair HX1000i
Philips Momentum 3000 24" (Main) & MSI Optix G241V E2 (Second)
Lian Li O11D
Roccat Vulcan 120 Aimo, Roccat Kone Aimo Remastered and Roccat Sym Pro Air
Core i7 10700KF 5Ghz @ 1.25v With Alphacool Eisblock XPX Aurora Edge
Gigabyte RTX 2080 Super 1980Mhz @ 0.925v With TechN GPU Block
32Gb Corsair Vengeance RGB Pro 3600Mhz 16-18-18-38
Aqua Computer Ultitube 200 Pro D5 Next
Corsair XR5 240mm x2 & 360mm
Intel 670p 2Tb & WD Blue M.2 2Tb
Corsair HX1000i
Philips Momentum 3000 24" (Main) & MSI Optix G241V E2 (Second)
Lian Li O11D
Roccat Vulcan 120 Aimo, Roccat Kone Aimo Remastered and Roccat Sym Pro Air
- Apoptosis
- Site Admin
- Posts: 33941
- Joined: Sun Oct 05, 2003 8:45 pm
- Location: St. Louis, Missouri
- Contact:
Re: POST Crashing?
what happens if you unplug all the IDE and SATA devices except for the drive that the OS is installed on? See what that does... If it works start plugging in things one at a time until the system starts crashing. You can sometimes do this to isolate a bad device or one that isn't playing nice with the BIOS I/O tables.
Now might be a good time to check for any BIOS updates that need to be done and/or reset the BIOS to factory defaults as well.
Now might be a good time to check for any BIOS updates that need to be done and/or reset the BIOS to factory defaults as well.
Re: POST Crashing?
Ok so development on this issue.
It stopped doing this all the time but still quite often.
But the other day I opened her up removed a stick of RAM, to see the spec of said RAM and then popped the it back in. So the RAM was out for about 30 seconds and, as always when I open the tower up, unplugged everything. Since then it hasn't "crashed" just loads up like it should.
My question is this.
Could RAM that is seated incorrectly still be used by the PC but cause small issues in the BIOS and POST??
Neptune24
It stopped doing this all the time but still quite often.
But the other day I opened her up removed a stick of RAM, to see the spec of said RAM and then popped the it back in. So the RAM was out for about 30 seconds and, as always when I open the tower up, unplugged everything. Since then it hasn't "crashed" just loads up like it should.
My question is this.
Could RAM that is seated incorrectly still be used by the PC but cause small issues in the BIOS and POST??
Neptune24
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600)
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
- kenc51
- Legit Extremist
- Posts: 5167
- Joined: Thu Jun 23, 2005 1:56 pm
- Location: Dublin, Republic of Ireland
- Contact:
Re: POST Crashing?
DefinitelyNeptune24 wrote: My question is this.
Could RAM that is seated incorrectly still be used by the PC but cause small issues in the BIOS and POST??
Neptune24
It can cause timing issues and have the clock skew be off.
When / if the ram is put under stress it can cause a crash.
I suspect windows is smart enough to notice this and in its dump report it logs the bad memory address's.
This is why it boots the second time as it ignore that address space. Server BIOS's & OS's have been doing this for years
I highly suggest you run a few passes of Memtest86+ to be on the safe side
Re: POST Crashing?
Ok thank you but I am going to replace the RAM anyway fairly soon. So once I have done that, I shall do some memory tests.
Neptune24
Neptune24
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600)
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
- kenc51
- Legit Extremist
- Posts: 5167
- Joined: Thu Jun 23, 2005 1:56 pm
- Location: Dublin, Republic of Ireland
- Contact:
Re: POST Crashing?
Do the tests before! It might not be the ram, its unlikely but it can be the slots.Neptune24 wrote:Ok thank you but I am going to replace the RAM anyway fairly soon. So once I have done that, I shall do some memory tests.
Neptune24
If you switch the them to alternate slots it might clear things up.
To run memtest it only takes time. It's simple to do and always worth having on a CD / USB key.
http://www.memtest.org/download/4.20/me ... taller.zip
This will install it to usb
http://www.memtest.org/download/4.20/me ... 20.iso.zip
This is for CD
It takes ~10 mins per GB of ram to test, i suggest 5x passes (do it while having dinner etc)
In the old days you could just run tests 5 & 8 to find errors quickly, but things have proly changed in the last 3 years
You could also try increase the memory voltage by one notch (~0.1v)
This will cause no long term problems to the memory or other parts, but may fix it
Ken
Re: POST Crashing? Solvedish
Ok so intalled the new RAM and ran those tests and all is well. And the PC is considerably faster too.
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7600)
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11
Mother Board: Gigabyte GA-880GM-UD2H
BIOS: Award Modular BIOS v6.00PG
Processor: AMD PhenomII X4 965 Processor, 3.4GHz(Stock)
Memory: 16GB RAM
Graphics Card: GeForce GTX 550 Ti Memory: 1024 MB
GPU Driver: 8.17.12.7061
Direct X 11